Hardness & roughness & toughness
Calibrations conform to the requirements of
Brinell ISO 6506-2 or ASTM E10
Vickers ISO 6507-2 or ASTM 384
Rockwell ISO 6508-2 or ASTM E18
Leeb ISO 16859-2 Accreditation applies to indirect and direct method
Calibrations conform to the requirements of
ISO 18898, ISO 7619-1
- Reference harness blocks – Shore, IRHD, Rockwell, Brinell, Vickers, Leeb
|
The calibration procedure is non-accredited
- Instruments for Roughness measurement
|
Range of accredited procedure
from 0,065 µm to 1,63 µm- Reference roughness blocks
|
Non-accredited calibration procedure can be performed
from 0,065 µm to 1,63 µmCalibrations conform to the requirements of
ISO 13802, ISO 148-2Range of accredited procedure
from 0,2 J to 50 J Non-accredited calibration procedure can be performed
to 750 J
Related content
Testing
We perform testing through the entire life–cycle of yoursample — from raw material to material, half–product, orproduct and waste.
MORE
Control and verification
In LOTRIČ Metrology we control and varificare based on a wide range of legal criteria.
MORE
Metrology solutions
Our users swear to one of the three ways of colaboration.
MORE
Acceleration & mass balance
- Acceleration and Deceleration measuring instruments
|
Range of accredited procedure
to 9,806 m/s2 Range of accredited procedure
to 100 g mm Non-accredited calibration procedure can be performed
from -10° to 10°
Related content
Control and verification
In LOTRIČ Metrology we control and varificare based on a wide range of legal criteria.
MORE
Metrology solutions
Our users swear to one of the three ways of colaboration.
MORE
All calibrations
Mass & Pressure
- Non-automatic weighing instruments
|
Calibrations conform to the requirements of
EURAMET/cg-18, USPC 1251/41, EDQM/OMCL Range of accredited procedure
from 1 mg to 100.000 kgNon-accredited calibration procedure can be performed
to 200.000 kgInspection conform to the requirements of
USPC 1251/41Range of accredited procedure
from 1 mg (micro, analytical and precision balances)- Weights and objects of any other mass
|
Calibrations conform to the requirements of
OIML R111-1, DKD Range of accredited procedure
from 1 mg to 500 kgE2 from 1 mg to 2 kg
F1 from 1 mg to 20 kg
F2 from 1 mg to 50 kg
M from 1 mg to 500 kgNon-accredited calibration procedure can be performed for mass
higher than 500 kg
Calibrations conform to the requirements of
EURAMET/cg-17, DKD-R 6-1Range of accredited procedure
from -0,95 bar to 1000 barCalibrations conform to the requirements of
EURAMET/cg-17Range of accredited procedure
from 100 mbar to 2000 mbar
Volume & Density
- Volumetric apparatus – pipettes, dispensers, burettes, titrators
|
Calibrations conform to the requirements of
ISO 8655-6Range of accredited procedure
to 200 ml- Graduated Cylinders and Bottles
|
Calibrations conform to the requirements of
EURAMET/cg-19, ISO 4787 Range of accredited procedure
to 2000 ml Non-accredited calibration procedure can be performed
to 50 lCalibrations conform to the requirements of
EN 12350-7, ASTM C231Range of accredited procedure
from 1 l to 10 l- Automated liquid handling systems (ALHS)
|
Calibrations conform to the requirements of
IWA 15 and ISO 8655-6Range of accredited procedure
to 2000 µl- Volumetric dosing systems – volume of flow
|
Range of accredited procedure
to 500 l Non-accredited calibration procedure can be performed
to 1000 l
Range of accredited procedure
to 350 lNon-accredited calibration procedure can be performed
to 1000 lRange of accredited procedure
to 200 cm3Non-accredited calibration procedure can be performed
to 2000 cm3Calibrations conform to the requirements of
ISO 649-2, ASTM E-126Range of accredited procedure
from 600 kg/m3 to 2000 kg/m3- Density of liquids and solids
|
Non-accredited calibration procedure can be performed
from 500 kg/m3 to 15000 kg/m3
pH & gas analysers
Calibrations conform to the requirements of
IEC 60746-2Range of accredited procedure
from 0 ph/-1999 mV to 12,45 ph/1999 mV
Calibrations conform to the requirements of
IEC 60746-3Range of accredited procedure
from 0,04 µS/cm to 800 µS/cmCalibrations conform to the requirements of
IEC 60746-3Range of accredited procedure
to 3,5 %Calibrations conform to the requirements of
OIML R142Non-accredited calibration procedure can be performed
in units Brix, °C, %
Calibrations conform to the requirements of
OIML R99Accredited procedure can be performed for gases
CO2, CO, O2, C3H8Calibrations conform to the requirements of
OIML R99Range of accredited procedure
to 100 %Non-accredited calibration procedure can be performed for gases
CO2, CO, O2, H2Non-accredited calibration procedure can be performed for gases
CO2, CO, O2, H2, CH4, LPG
Flow & velocity
Range of accredited procedure
from 10 ml/min (0,012 g/min) to 100 l/min (120 g/min) For higher values, a non-accredited calibration procedure can be performed.
Range of accredited procedure f
rom 0,3 m/s to 40 m/s
Range of accredited procedure
from 0° to 360°
Electricity & photometry
Range of accredited procedure
to 1020 VRange of accredited procedure
to 20,5 ARange of accredited procedure
to 110 kΩRange of accredited procedure
from 0,3 W to 96 kW
Range of accredited procedure
from 2 lx to 5000 lx Non-accredited calibration procedure can be performed
to 20000 lxRange of accredited procedure
to 5 %Range of accredited procedure
to 100 %Range of accredited procedure
to 100 GU
Time & frequency
Range of accredited procedure
to 24 hFor higher values, a non-accredited calibration procedure can be performed
Range of accredited procedure
to 99999 min-1
Range of accredited procedure
from 10 km/h to 250 km/hFor higher values, a non-accredited calibration procedure can be performed
- Equipment for Tachograph inspection
|
Range of accredited procedure
Speed from 20 km/h (13 Hz) to 180 km/h (1200 Hz)Time interval to 24 h
Travelled distance from 1000 m to 10000 m
Acoustics & vibrations
- Fonometers and Acoustical calibrators
|
Calibrations conform to the requirements of
IEC 61252, IEC 60942, IEC 61094Range of accredited procedure
from 10 dB to 160 dB - Accelerometer Calibrators
|
Range of accredited procedure
from 100 mm/s2 (50 µV) to 100 m/s2 (50 V)
Calibrations conform to the requirements of
ISO 8041, ISO 5358, ISO 2631Range of accredited procedure
from 100 mm/s2 (50 µV) to 3500 m/s2 (50 V)Range of accredited procedure
from 0 dB to 60 dB
Temperature & humidity
- Thermometers (Resistance, glass, with indicators, Thermocouples)
|
Range of accredited procedure
from -90 °C to 1100 °C- Resistance Thermometers, Thermocouples Indicators and Simulators
|
Calibrations conform to the requirements of
EURAMET/cg-11 Range of accredited procedure
from -260 °C to 1760 °C- Radiation and Ear Thermometers
|
Range of accredited procedure
from -40 °C to 500 °CRange of accredited procedure
from -70 °C to 300 °CNon-accredited calibration procedure can be performed
to 1100 °C- Climatic chamber and rooms
|
Calibrations conform to the requirements of
EURAMET/cg-20, DKD-R 5-7, IEC 60068-3-5Range of accredited procedure
from -80 °C to 280 °C
from 10 % to 95 %
- Steam sterilizers, Autoclaves
|
Range of accredited procedure
from -40 °C to 140 °C
from 0,1 bar to 5 barCalibrations conform to the requirements of
EURAMET/cg-13Range of accredited procedure
from -90 °C to 400 °CNon-accredited calibration procedure can be performed
to 1100 °CRange of accredited procedure
from 50 °C to 1100 °CNon-accredited calibration procedure can be performed
to 1700 °C- Relative Humidity sensors – hygrometers
|
Range of accredited procedure
from 10 % to 95 %
Non-accredited calibration procedure can be performed
to 100 %
Force & torque
Range of accredited procedure
from 1 N to 5 kN Non-accredited calibration procedure can be performed
to 100 kNCalibrations conform to the requirements of
ISO 7500-1Range of accredited procedure
from 0,2 kN to 200 kN for tension/compressionRange of accredited procedure
from 0,2 kN to 3000 kN for pressure- Extensometers – position measurement of the crosshead
|
Range of accredited procedure
to 1000 mm- Concrete testing machines
|
Calibrations conform to the requirements of
ISO 12390-4Range of accredited procedure
from 0,2 kN to 3000 kN
Calibrations conform to the requirements of
ISO 6789Range of accredited procedure
from 0,1 Nm to 3000 NmCalibrations conform to the requirements of
EURAMET/cg-14Non-accredited calibration procedure can be performed
from 0,1 Nm to 3000 NmRange of accredited procedure
from 0,1 kN to 6 kN for cars and mopedsCalibrations
for trucks conform to the requirements of
ISO 21069-1Range of accredited procedure
from 0,1 kN to 40 kN
- Levers for calibration of roll brake tester
|
Calibration of direct lever force
Range of accredited procedure
from 0,2 kN to 20 kN
Length & form
- Gauge Blocks (standard, square, cylindrical, optical flats)
|
Calibrations conform to the requirements of
ISO 3650Range of accredited procedure
from 0,5 mm to 1000 mm
- Ring gauges and plug gauges (plain, screw, taper)
|
Calibrations conform to the requirements of
EURAMET/cg-10Range of accredited procedure
to 800 mm- Gauges (Thickness and Gap gauges, Sphere (ball) diameter, Step gauges)
|
Range of accredited procedure
to 1000 mm- Callipers, micrometers, dial gauges
|
Calibrations conform to the requirements of
ISO 13385, ISO 13225, ISO 3611, VDE 2618Range of accredited procedure
to 3000 mm- Dial gauges, Electronic probes
|
Calibrations conform to the requirements of
ISO 13102, ISO 463, ISO 9493, VDE 2618Range of accredited procedure
to 200 mmNon-accredited calibration procedure can be performed
to 1000 mm- Tape measures, rulers and laser distance meters (glass rulers, tape measures)
|
Range of accredited procedure
Rulers to 4000 mm
Laser meters to 60 m
Tape measures to 200 m
- Ultrasonic and Magnetic thickness gauges
|
Range of accredited procedure
to 50 mm - Distance measuring Wheels, Measuring wheels with counters
|
Range of accredited procedure
to 1000 m Range of accredited procedure
to 1000 mmNon-accredited calibration procedure can be performed
to 10 m
Calibrations conform to the requirements of
ISO 13060Range of accredited procedure
to (200 x 300) mm Non-accredited calibration procedure can be performed
to (750 x 750) mmCalibrations conform to the requirements of
ISO 13060Range of accredited procedure
to (1500 x 1500) mm Non-accredited calibration procedure can be performed
to (4000 x 2500) mm
Angle & inclination
Range of accredited procedure
from 0,1° to 360°Range of accredited procedure
from -5 mm/m to 5 mm/mRange of accredited procedure
to 360°
Calibrations conform to the requirements of
BS 3064Range of accredited procedure
to 500 mm- Surface plates, Rulers, Squares (flatness and parallelism)
|
Range of accredited procedure
to 1000 mm Calibrations conform to the requirements of
ISO 3310-1, ISO 3310-2Range of accredited procedure
to 400 mm
Hardness & roughness & toughness
Calibrations conform to the requirements of
Brinell ISO 6506-2 or ASTM E10
Vickers ISO 6507-2 or ASTM 384
Rockwell ISO 6508-2 or ASTM E18
Leeb ISO 16859-2 Accreditation applies to indirect and direct method
Calibrations conform to the requirements of
ISO 18898, ISO 7619-1
- Reference harness blocks – Shore, IRHD, Rockwell, Brinell, Vickers, Leeb
|
The calibration procedure is non-accredited
- Instruments for Roughness measurement
|
Range of accredited procedure
from 0,065 µm to 1,63 µm- Reference roughness blocks
|
Non-accredited calibration procedure can be performed
from 0,065 µm to 1,63 µmCalibrations conform to the requirements of
ISO 13802, ISO 148-2Range of accredited procedure
from 0,2 J to 50 J Non-accredited calibration procedure can be performed
to 750 J
Acceleration & mass balance
- Acceleration and Deceleration measuring instruments
|
Range of accredited procedure
to 9,806 m/s2 Range of accredited procedure
to 100 g mm Non-accredited calibration procedure can be performed
from -10° to 10°
Related content
Testing
We perform testing through the entire life–cycle of yoursample — from raw material to material, half–product, orproduct and waste.
MORE
Control and verification
In LOTRIČ Metrology we control and varificare based on a wide range of legal criteria.
MORE
Metrology solutions
Our users swear to one of the three ways of colaboration.
MORE